Sửa chữa Servopack Yaskawa SGDM-15ADA lỗi không lên nguồn

CNCRITECH đã sửa thành công bộ Servopack Yaskawa SGDM-15ADA công suất 1.5kw thuộc dòng Sigma-2 bị lỗi không lên nguồn rất thường gặp ở dòng này do dòng Servopack này đời đã khá sâu nên đã được sử dụng trong khoảng thời gian dài tầm 5 đến 10 năm nên phát sinh lỗi không lên gì màn hình tối om

sua-chua-servo-yaskawa-sgdm-15ada-3

Lỗi không lên gì ở dòng Servopack Yaskawa Sigma 2 này chủ yếu do hoạt động lâu ngày linh kiện đến tuổi thọ bị chết hoặc do sử dụng bụi bặm vào làm chập ở bên trong gây ra. Công ty chúng tôi đã xử lý thành công rất nhiều bộ SGDM bị lỗi này để tránh gặp lỗi này quý khách hàng nên có kế hoạch bảo trì bảo dưỡng thiết bị thường xuyên.

Xem thêm: sửa chữa các lỗi servo Yaskawa 100, 410, 7AB, 030, B33, 400

sua-chua-servo-yaskawa-sgdm-15ada-6

sua-chua-servo-yaskawa-sgdm-15ada-4sua-chua-servo-yaskawa-sgdm-15ada-2

Sau khi sửa chữa xong bộ Servo pack Yaskawa SGDM-15ADA đã lên nguồn bình thường

sua-chua-servo-yaskawa-sgdm-15ada-1

Bảng mã lỗi Servo Yaskawa SGDM

A.02 : Parameter Breakdown (The EEPROM data storing the parameter is incorrect.)

A.03 : Main Circuit Encoder Error (Not detected for  the SERVOPACK with the  capacity of 6.0 kW or more)

A.04 : Parameter Setting Error (The parameter setting was out of the allowable setting range.)

A.05 : Combination Error (The SERVOPACK and ser -vomotor capacities do not correspond.)

A.09 : Dividing Ratio Setting Error

A.0A : Encoder Model Unmatched

A.10 : Overcurrent (An overcurrent flowed through the IGBT) or Heat Sink Overheated

A.30 : Regeneration Error Detected (Detected when the power to the main circuit was turned ON.)

A.32 : Regenerative Overload (Detected when the power to the main circuit is turned ON.)

A.33 : Main Circuit Wiring Error (Detected when the power to the main circuit is turned ON.)

A.40 : Overvoltage∗1 (Detected when the SERVOPACK’s main circuit DC voltage is 420 V or more.) (Detected when
the power to the main circuit is turned ON.)

A.41 : Undervoltage ∗1 (Detected when the SERVOPACK’s main circuit DC voltage is 170 V or less.) (Detected when the power to the main circuit is turned ON.)

A.51 : Overspeed (Detected when the feedback speed is the maximum motor speed × 1.2 or more for the SGMGH servomotor, and × 1.1 or more for the other servomotors.)

A.71 : High Load

A.72 : Low Load

A.73 : Dynamic Brake Overload

A.74 : Overload of Surge Current Limit Resistor (Detected when the number of times that the main circuit’s power is turned ON or OFF more than 10 times/2 seconds.)

A.7A : Heat Sink Overheated (Detected when the heat sink temperature exceeds 100 ×°C.)

A.81 : Encoder Backup Error (Detected on the encoder side.) (Only when an absolute encoder is connected.)

A.82 : Encoder Checksum Error (Detected on the encoder side.)

A.83 : Absolute Encoder Battery Error (Detected when the battery voltage is lower than the specified value 2 to 4 s after the control power supply is turned ON.) (Only when an absolute encoder is connected.)

A.84 : Encoder Data Error (Detected on the encoder side.)

A.85 : Encoder Overspeed (Detected when the encoder power supply was turned ON.) (Detected on the encoder side.)

A.86 : Encoder Overheated (Only when an absolute encoder is connected.)(Detected on the encoder side.)

A.b1 : Reference Speed Input Read Error (Detected when the Servo is ON.)

A.b2 : Reference Torque Input Read Error (Detected when the servo is ON.)

A.b3 : Current Detection Error

A.bF : System Alarm

A.C1 : Servo Overrun Detected

A.C8 : Absolute Encoder Clear Error and Multiturn Limit Setting Error

A.C9 : Encoder Communications Error

A.CA : Encoder Parameter Error

A.Cb : Encoder Echoback Error

A.CC : Multiturn Limit Disagreement

A.d0 : Position Error Pulse Overflow

A.F1 : Power Line Open Phase

A.F5, A.F6 : Servomotor Disconnection Alarm The power is not supplied to the servomotor though the SERVOPACK received the
Servo ON command

CPF00 : Digital Operator Transmission Error 1

CPF01 : Digital Operator Transmission Error 2

A.90 : Excessive Position Error Warning: Warning for the alarm A.d0 (In servo ON status, the position error pulses exceed the excessive position error warning level set in the parameter Pn51E.)

A.91 : Overload: Warning for the alarms A71 and A72 In either of the following cases:1. 20% of the overload detection level
of A71 2. 20% of the overload detection level of A72.

A.92 : Regenerative Overload: Warning for the alarm A320

A.93 : Absolute Encoder Battery Warning (The battery voltage stays below the specified value 4 seconds after the control power supply was turned ON.)(Only when an absolute encoder is connected.)

Trả lời

Email của bạn sẽ không được hiển thị công khai. Các trường bắt buộc được đánh dấu *